Goodman Furnace · GMVC96 two-stage variable-speed furnaces

Goodman Two-Stage Furnace Blower Motor Codes (b0, b1, b2, b3, b4, b5, b7, b9)

These codes on GMVC96 two-stage furnaces relate to the variable-speed (ECM) blower motor: not running, lost communication, mismatch, limiting, trips, locked rotor, parameters and low airflow. Several are caused or made worse by clogged filters and restrictive ductwork, so check the filter first.

Safety: Involves gas, venting, refrigerant or electrical parts. Do the basic checks only, then call a licensed technician.

b0ECM Blower Motor Not Running

The control doesn't detect the blower motor running when it should, so the furnace won't operate.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: B0 · From a service manual · checked 2026-11-21

b1ECM Motor Communications Lost

The control can't communicate with the blower motor.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: B1 · From a service manual · checked 2026-11-21

b2Motor Horsepower Mismatch

The installed blower motor's horsepower doesn't match the furnace's data.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: B2 · From a service manual · checked 2026-11-21

b3ECM Motor Operating in a Limiting Condition

The blower is limiting power, speed or temperature and delivering less airflow, often due to clogged filters or restrictive ducts.

  1. Replace or clean the furnace air filter and make sure supply and return vents are open
  2. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  3. If the code returns, call a licensed HVAC technician

Also shown as: B3 · From a service manual · checked 2026-11-21

b4Motor Trips

The blower motor lost control or overloaded and shut down, often from sudden duct blockages or high loading.

  1. Replace or clean the furnace air filter and make sure supply and return vents are open
  2. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  3. If the code returns, call a licensed HVAC technician

Also shown as: B4 · From a service manual · checked 2026-11-21

b5Motor Locked Rotor

The blower motor failed to start after 10 attempts: obstruction, seized bearings or failed motor.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: B5 · From a service manual · checked 2026-11-21

b7Motor Parameters

The motor didn't get the information it needs or failed to start after 40 attempts.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: B7 · From a service manual · checked 2026-11-21

b9Low Indoor Airflow

Indoor airflow dropped below the calculated minimum, usually from clogged filters or restrictive ductwork.

  1. Replace or clean the furnace air filter and make sure supply and return vents are open
  2. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  3. If the code returns, call a licensed HVAC technician

Also shown as: B9 · From a service manual · checked 2026-11-21

Parts and supplies for this fix

We may earn a commission from purchases made through these links. Confirm the part matches your exact model number before buying.

Sources

Spotted an error on this page? Report it and we'll re-check it against the manual.