Goodman Furnace · GM9S single-stage 92%/96% furnaces

Goodman Single-Stage Furnace Control Codes (EEE, EEL, EEA, EEb, EEC, EEn, EEj, EEH, E10)

These seven-segment codes on GM9S single-stage furnaces point to the integrated control, igniter relay, gas valve circuits, inducer relay, twinning, polarity or grounding. All of them are technician repairs; the only homeowner step is a reset.

Safety: Involves gas, venting, refrigerant or electrical parts. Do the basic checks only, then call a licensed technician.

E10Grounding Error

The furnace isn't properly grounded.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: e10 · From a service manual · checked 2026-11-21

EEAReversed Line Polarity or Grounding Error

Line voltage polarity is reversed or the furnace isn't properly grounded.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eea · From a service manual · checked 2026-11-21

EEbInternal Gas Valve Error

The control detected an internal gas valve circuit error.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: EEB, eeb · From a service manual · checked 2026-11-21

EECExternal Gas Valve Error

The control detected an external gas valve circuit error.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eec · From a service manual · checked 2026-11-21

EEEInternal Faults or IRQ Loss

The integrated control detected an internal fault.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eee · From a service manual · checked 2026-11-21

EEHTWIN Error

A fault in a twinned (two-furnace) installation.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eeh · From a service manual · checked 2026-11-21

EEjInducer Relay Error

The draft inducer relay on the control isn't working correctly.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eej, EEJ · From a service manual · checked 2026-11-21

EELIgnitor Relay Fault

The igniter relay on the control isn't working correctly.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: eel · From a service manual · checked 2026-11-21

EEnIgnitor Open

The igniter circuit is open, usually a broken or disconnected igniter.

  1. Reset: turn the thermostat off for 5–20 seconds and back on, or switch off power to the furnace for at least 5 seconds
  2. If the code returns, call a licensed HVAC technician

Also shown as: een, EEN · From a service manual · checked 2026-11-21

Parts and supplies for this fix

We may earn a commission from purchases made through these links. Confirm the part matches your exact model number before buying.

Sources

Spotted an error on this page? Report it and we'll re-check it against the manual.